die cast hydraulic cylinder Sold to Ethiopia

This article mainly introduces:

Ethiopia hydraulic cylinder,die cast hydraulic cylinder manufacturer,die cast hydraulic cylinder

(Ethiopia die cast hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

die cast hydraulic cylinder are widely used in Ethiopia，because of excellent fatigue and impact resistance，no need for deceleration device，long service life.So our company has designed die cast hydraulic cylinder for customers from Ethiopia.

Introduction to die cast hydraulic cylinder:

die cast hydraulic cylinder buffer valve inspection and maintenance: For the valve buffer die cast hydraulic cylinder, the focus should be on checking the wear of the buffer valve spool and seat. Once it is found that the amount of wear increases and the seal fails, it should be replaced. It can also be repaired by using abrasive spool and seat matching grinding method.

die cast hydraulic cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

The die cast hydraulic cylinder should be vented: when the die cast hydraulic cylinder is installed or parked for a long time to work again, the air will penetrate into the die cast hydraulic cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the die cast hydraulic cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the die cast hydraulic cylinder, the oil is best entered and discharged from the highest point of the die cast hydraulic cylinder. die cast hydraulic cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

Improve the service life of the die cast hydraulic cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the die cast hydraulic cylinder (such as the die cast hydraulic cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the die cast hydraulic cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the die cast hydraulic cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single die cast hydraulic cylinder exhaust.

Answers to some questions about die cast hydraulic cylinder:

What is the cause of the deep scratch of the cylinder?
The following reasons can cause the cylinder to be scratched. 1: Hydraulic oil containing particulate impurities into the hydraulic cylinder, these particulate impurities stuck between the piston rod and the guide ring (or stuck between the piston and the inner wall of the cylinder), when the piston movement in the cylinder will scratch the piston rod, the phenomenon of the inner wall of the cylinder, the more particles, the larger the scratch marks the deeper and more obvious. 2: The body of the cylinder itself. Due to assembly or design reasons, the coaxial error between the piston rod, piston, cylinder, guide ring and other parts is too large, or the cylinder, piston rod straightness error is too large, so that the piston rod and the guide ring interference between the cylinder, this mechanical interference will certainly lose the piston rod or cylinder wall.

How to disassemble the big nut that excavate the oil cylinder piston of the excavator?
If you want to be safe, look for a special unloading place for this thing, which is an oil cylinder on top of a turntable with a large nut attached to the center of the turntable. If you're in the field just pin the head of the cylinder to one end, use a big homemade wrench to hold the nut in place, and then get a digging machine and push it down, and it opens.