Release time：2023-11-24 08:39:06 Hits： Current position: Home > News
This article mainly introduces:
Nigeria hydraulic cylinder,trailer hydraulic cylinder manufacturer,trailer hydraulic cylinder
(Nigeria trailer hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）
trailer hydraulic cylinder are widely used in Nigeria，because of clever hydraulic energy conversion，no transmission clearance，powerful torque.So our company has designed trailer hydraulic cylinder for customers from Nigeria.
trailer hydraulic cylinder use should try to avoid sealing belt into the trailer hydraulic cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the trailer hydraulic cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the trailer hydraulic cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.
If the piston rod and trailer hydraulic cylinder are stuck or the trailer hydraulic cylinder is blocked, at this time, no matter how to operate, the trailer hydraulic cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the trailer hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.
trailer hydraulic cylinder is the most important part of construction machinery, the traditional processing method is: broaching trailer hydraulic cylinder block - fine boring trailer hydraulic cylinder block - grinding trailer hydraulic cylinder block. The rolling method is: broaching trailer hydraulic cylinder block - fine boring trailer hydraulic cylinder block - rolling trailer hydraulic cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the trailer hydraulic cylinder block is about 1-2 days, rolling 1 meter of the trailer hydraulic cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the trailer hydraulic cylinder increases by 25%. If the trailer hydraulic cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality trailer hydraulic cylinders, you must take the rolling production process. After the trailer hydraulic cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.
The scar on the sliding surface of the trailer hydraulic cylinder piston will transfer with use. Before the piston is installed, there are scars on its sliding surface, which are installed intact and untreated, and these scars will in turn scratch the inner surface of the trailer hydraulic cylinder wall. Therefore, before installation, these scars must be fully repaired.
What hydraulic oil does servo cylinder generally use?
The medium used by the cylinder generally depends on the working condition of the use, including pressure, installation environment, sealing material, etc. I think the first thing to consider is the impact of the sealing material. Mineral oil is a good choice if it is not too fire-resistant or used in a high temperature environment. 1, servo cylinder features: closed-loop servo control, control accuracy of 0.01mm; Precise control of thrust, increase pressure sensor, control accuracy up to 1%; It is easy to connect with PLC and other control systems to achieve high precision motion control. Low noise, energy saving, clean, high rigidity, impact resistance, long life, simple operation and maintenance. 2, the servo cylinder can be fault-free in harsh environments, and the protection level can reach IP66.
Hydraulic system schematic diagram, pipeline identification S and L, respectively corresponding nominal diameters? 16S is equivalent to DN12 high-pressure cylinder, and 15L means what?
16S refers to the high pressure series, outer diameter 16x2 steel pipe, the corresponding sleeve nut is M24X1.515L is the low pressure series, the outer diameter of 15x1.5 steel pipe, the corresponding sleeve nut is M22X1.5.
Add Wechat