rolling mill cylinder Sold to Belarus

This article mainly introduces:

Belarus hydraulic cylinder,rolling mill cylinder manufacturer,rolling mill cylinder

(Belarus rolling mill cylinder,produced by Hebei Hengyu company）

rolling mill cylinder are widely used in Belarus，because of excellent temperature resistance，no transmission clearance，simple structure and reliable operation.So our company has designed rolling mill cylinder for customers from Belarus.

Introduction to rolling mill cylinder:

When the rolling mill cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the rolling mill cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the rolling mill cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the rolling mill cylinder can meet the requirements by grinding. However, the life and reliability of this repair rolling mill cylinder are not high.

In order to ensure the service life of the rolling mill cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

The cavitation of the rolling mill cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the rolling mill cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

rolling mill cylinder piston rod material introduction: In general, we use 45 steel to produce rolling mill cylinder piston rod. It has a large impact force when it is used, and some good performance steel are also used in the heavy load transmission. In order to have enough work intensity when using, and can ensure normal use, this is still more critical to have a detailed understanding of the material.

Answers to some questions about rolling mill cylinder:

Is rubber or polyurethane better for V-ring of hydraulic cylinder?
The hydraulic cylinder V-type seal ring is better with polyurethane, and chlorine rubber is used for various chemicals and high temperatures, especially when there are wear-resistant requirements, polyurethane rubber is needed. But the price of polyurethane rubber is much more expensive than the price of rubber. However, the V-ring material is most commonly used in nitrile and neoprene rubber, and natural rubber is used for sealing water and air. Butyl rubber is used for non-combustible hydraulic fluids and phosphate ester hydraulic fluids. The advantage is that the price is cheaper than the polyurethane material, and the disadvantage is that it is not wear-resistant and the anti-aging property is relatively poor.

How to calculate the tonnage of the hydraulic press without konowing the diameter of the cylinder?
To know the tonnage of the hydraulic cylinder, you first need to know the working pressure of the hydraulic system, the inner diameter of the hydraulic cylinder and the outer diameter of the cylinder rod (the outer diameter of the cylinder rod is needed when calculating the hydraulic cylinder tension). The thrust of the hydraulic cylinder (that is, the force that the hydraulic cylinder can produce by extending out) = the cross-sectional area of the hydraulic cylinder (or the cross-sectional area of the piston) × the working pressure of the cylinder (the cross-sectional area of the piston) =pi*D^2/4= PI (take 3.14) × the square of the cross-sectional area of the piston ÷4 working pressure to see the pressure displayed on the pressure gauge when the maximum load is working.