High quality hydraulic equipment manufacturers!
        TELL:+8613184968882

        shearing machine cylinder Sold to Indonesia

        Release time:2023-11-28 10:55:40 Hits:112 Current position: Home > News

        This article mainly introduces:

        Indonesia hydraulic cylinder,shearing machine cylinder manufacturer,shearing machine cylinder

        Indonesia shearing machine cylinder

        (Indonesia shearing machine cylinder,produced by Hengyu Group)

        shearing machine cylinder are widely used in Indonesia,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed shearing machine cylinder for customers from Indonesia.

        Introduction to shearing machine cylinder:

        The wear of the hard chromium plating layer of the shearing machine cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

        When the shearing machine cylinder is disassembled due to oil leakage and other faults, the position of the piston should be moved to any end position of the shearing machine cylinder by applying liquid pressure. Improper tapping and sudden drop should be avoided during disassembly.

        The internal leakage of the shearing machine cylinder is an important indicator to measure the quality of the shearing machine cylinder: the internal leakage of the shearing machine cylinder will reduce the volumetric efficiency, increase the temperature rise of the oil, affect the positioning accuracy of the shearing machine cylinder, so that the shearing machine cylinder can not accurately and stably stop in a certain position of the shearing machine cylinder, so it is one of the main indicators of the shearing machine cylinder.

        The repair method of shearing machine cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

        Answers to some questions about shearing machine cylinder:

        What steel pipe does hydraulic cylinder use? This problem is very general. Carbon steel pipe or ordinary seamless steel pipe are all ok, but then there are rolling, quilting, heat treatment and other steps, and the requirements are different, the wall thickness is different, the material is different. It depends on the circumstances.

        How to distinguish the bucket cylinder from the bucket rod cylinder?
        It can be distinguished according to its installation and connection: one end of the bucket cylinder is connected with the bucket; The rod cylinder is not connected to the bucket. The bucket refers to the bucket installed on the excavator. According to the working mode, it is divided into backhoe bucket and shovel bucket, the backhoe bucket is commonly used. The boom and bucket rod are working device of the excavator, usually called the big arm and the forearm, which are mainly used to control the digging and loading of the bucket. The arm connected to the frame is longer, so it is commonly known as the big arm, and its term is called the boom. The arms connected to the digging bucket are smaller, so they are commonly known as the lower arms, and the term is called the bucket rod, so they are commonly known as the big lower arms.

        Back to list Recommended article

        Leave a message if you have any questions.

        Send
        Email

        Email:hsslrubbertech@gmail.com7x24 hours

        Glad to receive your consultation!:

        Service
        Tel

        +8613184968882
        7x24hours service

        Add
        Wechat

        Add Wechat
        TOP
        无码无套少妇毛多18p| 亚洲日本va午夜中文字幕久久| 精品高潮呻吟99av无码视频| 中文日韩亚洲欧美字幕| 无码中文字幕日韩专区视频| 免费精品久久久久久中文字幕| 亚洲.欧美.中文字幕在线观看| 日韩国产成人无码av毛片| 久久有码中文字幕| 99久久无色码中文字幕人妻| 久久精品无码一区二区三区| 亚洲av无码不卡一区二区三区| 亚洲美日韩Av中文字幕无码久久久妻妇 | 777久久精品一区二区三区无码| 中文无码久久精品| 国产精品亚洲w码日韩中文| 最近的中文字幕在线看视频| 国产成人无码精品久久久久免费| 亚洲乱码无码永久不卡在线| 一级中文字幕免费乱码专区| 日本中文字幕在线2020| 天堂√最新版中文在线| 午夜无码视频一区二区三区| 99久久精品无码一区二区毛片| 无码A级毛片免费视频内谢| 亚洲欧洲日产国码无码网站| 中文字幕AV中文字无码亚| 亚洲国产人成中文幕一级二级 | 亚洲欧美中文日韩在线v日本| 中文字幕aⅴ人妻一区二区 | 中文字幕无码免费久久| 亚洲av无码专区在线观看下载| 国产高新无码在线观看| 精品无码人妻久久久久久| 国产羞羞的视频在线观看 国产一级无码视频在线| 无码国产精品一区二区免费16| 亚洲av无码一区二区三区乱子伦| 亚洲中久无码永久在线观看同| 亚洲av无码一区二区三区在线播放| 亚洲AV无码精品无码麻豆| 久久久久久久亚洲Av无码|