tilting furnace hydraulic cylinder Sold to UAE

This article mainly introduces:

UAE hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

(UAE tilting furnace hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

tilting furnace hydraulic cylinder are widely used in UAE，because of excellent fatigue and impact resistance，no need for deceleration device，excellent temperature resistance.So our company has designed tilting furnace hydraulic cylinder for customers from UAE.

Introduction to tilting furnace hydraulic cylinder:

If the tilting furnace hydraulic cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the tilting furnace hydraulic cylinder. The internal parts of the tilting furnace hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the tilting furnace hydraulic cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the tilting furnace hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the tilting furnace hydraulic cylinder bore processing is out of whack. Because the piston and tilting furnace hydraulic cylinder, guide rail and piston rod are relative If the tilting furnace hydraulic cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling tilting furnace hydraulic cylinder weight composition and calculation. The weight of the tilting furnace hydraulic cylinder is composed of the tilting furnace hydraulic cylinder diameter, the outer diameter and weight of the tilting furnace hydraulic cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

At the rated pressure, the thrust of the tilting furnace hydraulic cylinder is determined by what factors: at the rated pressure of the oil pump, the work done by the tilting furnace hydraulic cylinder is related to the diameter of the tilting furnace hydraulic cylinder, but not to the stroke of the tilting furnace hydraulic cylinder. Moreover, the larger the tilting furnace hydraulic cylinder diameter, the larger the area, and the greater the pressure obtained. To this point, we should have a correct understanding and clear understanding, so as to avoid problems in the use of the tilting furnace hydraulic cylinder.

If the tilting furnace hydraulic cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

When the initial action of the tilting furnace hydraulic cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the tilting furnace hydraulic cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

Answers to some questions about tilting furnace hydraulic cylinder:

How to disassemble injection molding machine injection cylinder?
If it is not repaired for a long time, it is recommended to open both ends, comprehensively check the oil seal and piston ring inside, this is not much difficulty, pay attention to not install reverse when changing the oil seal, some piston rings are steel rings are rubber rings, and several interfaces of steel rings are not in the same position; Rubber ring pay attention not to install reverse; Be careful not to damage the oil seal when installing, otherwise it will soon leak oil.

What is the material of the lift cylinder?
The cylinder is composed of many parts. The cylinder also contains the seal and the installation port at both ends, the material of these two parts is not easy to determine if there is no physical object. The cylinder body is generally 20 steel, 45 steel, 27SiMn and other materials, and the piston rod is generally 40Cr, 45 steel and other materials.