High quality hydraulic equipment manufacturers!
        TELL:+8613184968882

        forklift steering cylinder Sold to Algeria

        Release time:2023-11-12 11:05:35 Hits:133 Current position: Home > News

        This article mainly introduces:

        Algeria hydraulic cylinder,forklift steering cylinder manufacturer,forklift steering cylinder

        Algeria forklift steering cylinder

        (Algeria forklift steering cylinder,produced by Hebei Hengyu company)

        forklift steering cylinder are widely used in Algeria,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed forklift steering cylinder for customers from Algeria.

        Introduction to forklift steering cylinder:

        The material of the sliding part of the forklift steering cylinder piston sintered casting piston will cause sintering phenomenon when subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.

        forklift steering cylinder seal leakage causes and countermeasures: a. Loose tie rod nut will cause leakage, tighten the tie rod nut according to the torque requirements of tie rod nut, test no leakage can continue to use. b. Pressure exceeding the limit will also cause leakage. Replace the forklift steering cylinder seal and re-tighten the tie rod nut to reduce the pressure to the nominal pressure range of the forklift steering cylinder. c. The forklift steering cylinder seal is extruded, if the O-ring is obviously extruded at the forklift steering cylinder seal, replace the forklift steering cylinder seal.

        Because of the slightly complex structure of the buffer forklift steering cylinder, sometimes there will be problems, such as when the forklift steering cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

        The internal leakage of the forklift steering cylinder is an important indicator to measure the quality of the forklift steering cylinder: the internal leakage of the forklift steering cylinder will reduce the volumetric efficiency, increase the temperature rise of the oil, affect the positioning accuracy of the forklift steering cylinder, so that the forklift steering cylinder can not accurately and stably stop in a certain position of the forklift steering cylinder, so it is one of the main indicators of the forklift steering cylinder.

        Answers to some questions about forklift steering cylinder:

        How to choose cylinder size, pump type, motor power for a 30-ton press?
        30 tons = 30,000 kg. It is expected to use a 16 mpa oil pump, then the cylinder area =30000/(160x3.14) and then square, the cylinder bore is 150 mm. Calculated at 500 mm travel per minute, the flow rate per minute is :0.75^2x3.14x5=8.8 liters/minute. Motor power =8.8x16/60=2.355. A 9 L/min, 16 mpa pump is available. Piston diameter 150 mm cylinder. 3 kW motor.

        What are the cylinder manufacturing processes?
        Hydraulic cylinder processing process: 1, cylinder: a, material preparation (seamless steel pipe) → inspection (material certificate, etc.) → tempering (outsourcing: Some parts) → car (car round, shelf mouth, boring, flange stop, etc.) → tempered hardness test → welding (welded pipe joint base, flange and other accessories) → boring or honing (rough boring, fine boring, rolling) → car (hole slot or internal and external thread) → fitter (drilling) → inspection → rust prevention storage b, material preparation (forgings) → inspection (material certificate, inspection, etc.) → welding (blank butt welding) → welding inspection → car (rough car) → quality control (outsourcing: some parts) → car (car round, shelf mouth, boring stop, flange stop, etc.)

        Back to list Recommended article

        Leave a message if you have any questions.

        Send
        Email

        Email:hsslrubbertech@gmail.com7x24 hours

        Glad to receive your consultation!:

        Service
        Tel

        +8613184968882
        7x24hours service

        Add
        Wechat

        Add Wechat
        TOP
        无码视频一区二区三区在线观看| 日韩精品无码免费专区网站 | 蜜芽亚洲av无码精品色午夜| 亚洲久本草在线中文字幕| 久久亚洲AV成人无码电影| 人妻丰满熟妇AV无码区HD| 亚洲中文字幕日产乱码高清app| 国产成人无码一区二区在线播放| 超清无码无卡中文字幕| 精品人妻中文字幕有码在线| 国产成人AV无码精品| 无码乱人伦一区二区亚洲| 综合久久久久久中文字幕亚洲国产国产综合一区首 | 久久久久无码精品国产不卡 | 亚洲啪啪AV无码片| 亚洲欧美精品一区久久中文字幕| 中文字幕无码精品亚洲资源网久久| 国产亚洲3p无码一区二区| 无码人妻精品一区二区三区66 | 中文字幕在线观看国产| 日韩乱码人妻无码中文字幕| 亚洲av无码专区在线观看下载| 在线看无码的免费网站| 99精品人妻无码专区在线视频区| 无码少妇一区二区三区浪潮AV| 最近高清中文在线字幕在线观看| 亚洲精品中文字幕无码蜜桃| 亚洲熟妇无码八V在线播放| 久久久久久无码国产精品中文字幕| 久久无码人妻一区二区三区午夜| 无码人妻久久一区二区三区 | AA区一区二区三无码精片| 人妻aⅴ无码一区二区三区| 无码精品久久久久久人妻中字| 亚洲AV无码成人精品区在线观看| 亚洲精品无码成人片久久| 亚洲AV无码成人精品区天堂| 欧洲精品久久久av无码电影| 国产成人无码一区二区三区| 人妻少妇看A偷人无码精品视频| 亚洲国产精品成人AV无码久久综合影院 |