yg series hydraulic cylinder Sold to Dominica

This article mainly introduces:

Dominica hydraulic cylinder,yg series hydraulic cylinder manufacturer,yg series hydraulic cylinder

(Dominica yg series hydraulic cylinder,produced by Hengyu Group）

yg series hydraulic cylinder are widely used in Dominica，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed yg series hydraulic cylinder for customers from Dominica.

Introduction to yg series hydraulic cylinder:

If the yg series hydraulic cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the yg series hydraulic cylinder. The internal parts of the yg series hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the yg series hydraulic cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the yg series hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the yg series hydraulic cylinder bore processing is out of whack. Because the piston and yg series hydraulic cylinder, guide rail and piston rod are relative If the yg series hydraulic cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling yg series hydraulic cylinder weight composition and calculation. The weight of the yg series hydraulic cylinder is composed of the yg series hydraulic cylinder diameter, the outer diameter and weight of the yg series hydraulic cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

The wear of the hard chromium plating layer of the yg series hydraulic cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

After chrome plating of the piston rod of the yg series hydraulic cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

When the yg series hydraulic cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the yg series hydraulic cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

Answers to some questions about yg series hydraulic cylinder:

What are the connection methods of the hydraulic cylinder? The connection modes of the cylinder and the actuator are earring connection, hinge shaft connection, thread connection, etc. The connection modes of tubing and cylinder are threaded connection, flange connection, etc.

How to calculate the hydraulic cylinder pressure? How much pressure can put up how much weight?
If you want to calculate the pressure of the cylinder, you must know the inner diameter of the cylinder, if the piston rod is needed to lift the weight, it should be: cylinder (no piston rod end) pressure = load (4000N) ÷{(PI /4)X the square of the cylinder diameter (mm) ", it has nothing to do with the piston rod diameter, the rod diameter of the piston rod is only related to the stability of the cylinder. The pressure inside the cylinder should be p=F/S=400×10/(3.14×(0.5×25)×(0.5×25))=8.15MPa which means that you need to provide at least that much pressure to complete the operation.