series synchronous cylinder Sold to UAE

This article mainly introduces:

UAE hydraulic cylinder,series synchronous cylinder manufacturer,series synchronous cylinder

(UAE series synchronous cylinder,produced by Hengyu Hydraulic Co., Ltd）

series synchronous cylinder are widely used in UAE，because of long service life，smooth movement，high work efficiency.So our company has designed series synchronous cylinder for customers from UAE.

Introduction to series synchronous cylinder:

Improve the service life of the series synchronous cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the series synchronous cylinder (such as the series synchronous cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the series synchronous cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the series synchronous cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single series synchronous cylinder exhaust.

The machining accuracy of the series synchronous cylinder depends on the level of equipment, production technology and testing means. series synchronous cylinder processing methods are commonly used in two ways, one is rough boring - fine boring - rolling, generally with 45# seamless steel pipe, this method of processing quality is good, but the cost is high. Another method is to use 20# cold-drawn seamless steel pipe, and then honing, the cost is lower. The piston rod must be adjusted and straightened before processing, and the coating thickness of the piston rod is generally not less than 0.03mm. The piston must be machined in strict accordance with the groove size and tolerance requirements given in the seal manual.

The series synchronous cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and does linear reciprocating motion (or swinging motion). It is simple in structure and reliable in operation. When it is used to achieve reciprocating movement, the deceleration device can be eliminated, and there is no transmission gap, and the movement is smooth, so it is widely used in various mechanical hydraulic systems. The output force of the series synchronous cylinder is proportional to the effective area of the piston and the pressure difference between the two sides; The series synchronous cylinder is basically composed of series synchronous cylinder and series synchronous cylinder head, piston and piston rod, sealing device, buffer device and exhaust device. Buffer device and exhaust device depending on the specific application, other devices are essential.

When installing the piston rod, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the series synchronous cylinder head adn the earring (or the middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent the phenomenon of rigid interference and causing unnecessary damage.

Answers to some questions about series synchronous cylinder:

The pressure gauge of the hydraulic station reaches 20MPa. How many tons of weight can the hydraulic cylinder lift? How to convert?
20Mpa=200kg/cm^2 The weight of the cylinder with a cross-sectional area of 1 square centimeter can be lifted is 200kg, so F=200X3.14X (125/2) ^2 =24531kg =24.5 tons.

Is rubber or polyurethane better for V-ring of hydraulic cylinder?
The hydraulic cylinder V-type seal ring is better with polyurethane, and chlorine rubber is used for various chemicals and high temperatures, especially when there are wear-resistant requirements, polyurethane rubber is needed. But the price of polyurethane rubber is much more expensive than the price of rubber. However, the V-ring material is most commonly used in nitrile and neoprene rubber, and natural rubber is used for sealing water and air. Butyl rubber is used for non-combustible hydraulic fluids and phosphate ester hydraulic fluids. The advantage is that the price is cheaper than the polyurethane material, and the disadvantage is that it is not wear-resistant and the anti-aging property is relatively poor.