stern plate hydraulic cylinder Sold to Korea

This article mainly introduces:

Korea hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

(Korea stern plate hydraulic cylinder,produced by Hebei Hengyu company）

stern plate hydraulic cylinder are widely used in Korea，because of powerful torque，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed stern plate hydraulic cylinder for customers from Korea.

Introduction to stern plate hydraulic cylinder:

When the stern plate hydraulic cylinder is customized, if there are high requirements for the quality of the stern plate hydraulic cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the stern plate hydraulic cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the stern plate hydraulic cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

In recent years, the processing process of the stern plate hydraulic cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

Causes and countermeasures of oil stern plate hydraulic cylinder leakage: Cast iron ring seal allows a certain degree of internal leakage. The impurities in the stern plate hydraulic cylinder will lead to premature wear of the piston seal, replace the piston seal; If the stern plate hydraulic cylinder is visibly scarred, the stern plate hydraulic cylinder must be replaced. It can be pressurized at one end of the stern plate hydraulic cylinder and opened at the other end of the oil port to observe whether there is obvious internal leakage at the end of the oil port. Most stern plate hydraulic cylinder piston drift may not come from the stern plate hydraulic cylinder, the above method to determine the stern plate hydraulic cylinder without internal leakage is helpful to determine the problem of the hydraulic system related components.

The cavitation of the stern plate hydraulic cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the stern plate hydraulic cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

Answers to some questions about stern plate hydraulic cylinder:

How to calculate the tonnage of the hydraulic press? Example: The input cylinder pressure is 5Mpa, the end area of the cylinder piston is 100mm, and how much is the thrust tonnage?
F=P*S=5*10^6*3.14*(1/20)^2=39250N.

Can pneumatic cylinder be used as hydraulic cylinder?
The pneumatic cylinder can only be used for pressure below 1MPA, and if it is used for hydraulic, the pressure should be under 1MPA, which may not meet the strength requirements. And the seals should use fluorine rubber to avoid corrosion. But pneumatic cylinder used as hydraulic cylinder is not whimsical, in fact, there is such a use. The pneumatic system has a natural defect, that is, the speed is unstable, especially in the case of low speed. The hydraulic pressure is very stable, if you do not want to buy a set of hydraulic system, while the strength of the cylinder is not large, you can use compressed air to push the hydraulic oil, with hydraulic oil to drive the cylinder, The force is the same as compressed air, but very smooth.